C3 Range
previous
next

C3 Range

The C3 Range of low voltage motor controllers
 
  • Compatible with all AC induction motors
  • 200Arms and 250Arms AC motor control power options
  • Intelligent Hill-Hold function
  • Versatile throttle input - resistive & voltage
  • Sophisticated low battery management
  • Integrated service timers
  • CANopen comms or CAN tiller compatible options
  • Electronics protected to IP65
  • Designed to meet EN1175, EN12895, and UL583 requirements
  • Sealed to IPx5
More Details

Overview

C3 Range

C3 - AC Motor Controller:


Although primarily intended for pallet truck-type applications(Class 3), the C3 AC motor controller is equally suitable for small ride-on machines. Two versions are available, 200Arms and 250Arms, thereby allowing the most cost-effective solution for an appliccation. 

  • Cost-effective, AC traction controller 
  • Programmable Belly-Button function 
  • Switched or proportional hydraulic control 
  • Five coil outputs 
  • Software interlocking of drive & hydraulics 
  • Designed to meet UL583 requirements 

Flexible yet straightforward programming means the C3 AC motor controllers are compatible with all types of AC induction motors. At the same time, a dedicated thermistor input allows motor temperature to be measured and the power to the motor to be reduced if it is becoming too warm.

SIMPLE MOTOR MATCHING: 
For ease of installation and efficient performance, C3 AC motor controllers can be ‘matched’ to any AC induction motor using an auto-commissioning sequence.

This simple 3-step process is launched via the C3 PC Programmer. No specialist measuring equipment is required, just the basic motor 'nameplate' data. 
Once commissioning has been completed on the first vehicle, the C3 programming file can be saved, copied, and then written to other vehicles equipped with the same motor type, significantly reducing set-up time. 

HILL-HOLD FUNCTION: 
To ensure maximum efficiency, the C3 employs an intelligent Hill-Hold function that only takes power from the battery if the vehicle starts to roll. As soon as it is detected that Hill-Hold is not required, then no further power will be consumed. Traditionally, the application of a brake switch has been needed to provide this function.


C3-36V - AC Motor Controller:


The C3-36V is a compact and cost-effective AC motor controller for small Industrial vehicles.
  • 36V AC traction controller, particularly suitable for ride-on floorcare machines
  • 200Arms motor output 
  • Three coil outputs
  • Programmable start-up sequence options
  • On-board Status LEDs
  • Designed to the requirements of EN60335-2-72 and UL583

POWERFUL AND VERSATILE:
Although primarily intended as an advanced, cost-effective, AC traction controller for floorcare machines, the 36V motor controller variant of PGDT’s C3 range is equally suitable for other small, ride-on vehicles. Flexible, yet simple programming means the controller is compatible with all types of AC induction motor, while a dedicated thermistor input allows motor temperature and the power to the motor to be reduced if it is becoming too warm.

ROBUST AND COMPLIANT: 
The innovative construction methods employed by the 36V motor controller ensure reliable and repeatable assembly of the electronic enclosure, which results in consistent protection of the electronic circuits from the environment and efficient transfer of heat to the baseplate. The design is compliant with all relevant international floorcare vehicle standards, e.g. EN60335-2-72 and uses UL approved materials throughout, taking into account the critical dimensions defined in UL583.

 

C3pump - AC/DC Motor Controller:

 

The C3pump AC/DC Motor Controller, which offers a combination motor controller, AC traction and DC pump controller drives, is an extension of Curtiss-Wright's high-performing, compact and cost-effective C3 family, but with all the specialist features needed for efficient and precise control of modern day stacker trucks.

  • All modern stacker truck functionality as standard 
  • 200Arms and 250Arms traction power options
  • 330Adc series motor pump drive
  • Programmable Belly-Button function
  • Programmable lift/lower speeds and rates
  • Five coil outputs 
  • Software interlocking of traction and hydraulics

Flexible, yet simple programming means the controller is compatible with all types on AC induction and DC series motors, while a dedicated thermistor input allows trction motor temperature and the power to the motor to be reduced if it is becoming too warm.  

The C3pump features up to eight dedicated digital inputs that can be individually switched to 0V, open-circuit, B+ or a combination of these options to provide the active state. The controller also accepts multiple throttle types, including 2- or 3-wire resistive and voltage. CAN tiller compatibly is provided as standard, offering vehicle OEMs maximum input flexibility.

The innovative construction methods employed by the C3pump ensure reliable and repeatable assembly of the electronic enclosure, which results in consistent protection of the electronic circuits from the environment and efficient transfer of heat to the baseplate. The design is compliant with all relevant international legislation and takes into account critical dimensions as defined by UL.

icon

C3 Product Brochure

Open Product Brochure
icon

C3-36V Product Brochure

Open Product Brochure
icon

C3pump Product Brochure

Open Product Brochure

This site uses cookies to improve our service, you can find out more here - for the best web experience please accept cookies

x